Home > Windows 7 > Bios Raid Bsod

Bios Raid Bsod

Contents

But since you're doing it on tiny disks, I don't suppose that's your use. –niXar Dec 12 '09 at 15:18 add a comment| 6 Answers 6 active oldest votes up vote I have a 750 gb hdd with the OS on it and two 80gb HDD. It is normally the same driver, and the same registry setting. Hardware & Devices SATA, AHCI, Raid compatabilitySo I'm setting up a M4N78 pro asus mobo for windows 7. this contact form

I mean why would I need to re-install operating system to add RAID setup? When you switch this, it appears as a completely different device to Windows, thus Windows basically says, "Hey! As I'm sure you know, there should be no difference (to Windows) for RAID vs AHCI. Now that Windows has the driver installed, it should be able to boot from it.

Ahci Blue Screen Windows 7

For added protection, back up the registry before you modify it. It would add more credibility to this answer. Not the answer you're looking for? FireBean, May 15, 2012 FireBean, May 15, 2012 #3 May 15, 2012 #4 David_CAN Limp Gawd Messages: 186 Joined: Aug 15, 2011 To boot in a reasonable amount of time Windows

windows-7 drivers raid raid-0 share|improve this question edited Dec 12 '09 at 14:53 asked Dec 11 '09 at 23:14 thegreyspot 72561629 What mode was the RAID adapter in when That should work. share|improve this answer answered Mar 31 '12 at 5:31 psyklopz 1485 Would they be AHCI drivers specific to my motherboard? Enable Ahci Windows 10 Still didnt work though, am I miss understanding that idealogy?

Why is [] + {} === {} + [] true? Just some quick and dirty synthetic benchmark numbers to whet your appetite at 4.5GHz with comparison to the i7-6700K at matched clocks. These are my steps: Settings > Integrated Peripherals > "SATA RAID/AHCI Mode" = RAID --> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs http://www.tomshardware.com/forum/294955-32-blue-screen-selecting-raid-intel-mode If those assumptions are wrong it will BSOD because the hardware isn't behaving how Windows thinks it will.

I made sure to write down the Serial numbers and also knew which SATA Ports each drive was plugged into.When I Exit the Raid Configuration screen, I receive a BSOD 0x0000007B.This Ahci Driver Power on computer and enter the BIOS. These are my steps:Settings > Integrated Peripherals > "SATA RAID/AHCI Mode" = RAID --> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are Special thanks go to Microsoft employee (O.

Enabling Ahci In Win 7 After Installation

Thanks. After cloning drive, reboot computer. Ahci Blue Screen Windows 7 Newer Than: Search this thread only Search this forum only Display results as threads More... Windows 10 Ide To Ahci It sees some problem(s), tries to repair, does not succeed and does not ask for drivers (which I put on a USB stick) to install.

thephatp View Public Profile Find More Posts by thephatp 31 Mar 2012 #4 thephatp Windows 7 Ultimate x64 SP1 15 posts No luck. weblink asked 7 years ago viewed 5454 times active 2 years ago Blog Stack Overflow Podcast #96 - A Face Full of Code Linked 1 Is it possible to enable RAID 1 Go here for the solution. Then reboot and change the above registry settings. Ahci Windows 7

Ask a new question Read More NAS / RAID Configuration Storage SATA Related Resources solved No drive is bootable in BIOS after switching to RAID solved Unable to boot BIOS menu The old was was also a Gateway DX4820. Then you set the OS ti AHCI. navigate here Below are the steps to accomplish the task.

Removing terms of certain degree in multivariable polynomial more hot questions question feed about us tour help blog chat data legal privacy policy work here advertising info mobile contact us feedback So, here follows the step-by-step guides I found, including the one I created myself: For Intel ICH8/ICH8R/ICH9/ICH9R controllers For AMD controllers: SB850/SB800 series (I wrote this one) :) SB700 series, and That was exactly what I needed.

Verify/Connect your hard drive to a SATA RAID port that supports IDE (refer to your BIOS or motherboard manual to determine port, on my board it was SATA 5 & 6).

Since your system disk will not be RAID, you need to move the drive you are booting from OFF of the ICH controller, and boot that disk on that controller in SSD RAID troubles after switching to new bay solved Lose my RAID 5 array in BIOS after overclock 2 RAID 0 SSD's are not booting to windows after switching motherboards. David's link worked like a charm. When the computer boots up, Windows 7 will install the AHCI drivers automatically.

However, serious problems might occur if you modify the registry incorrectly. Using your favorite image creating software (I use Acronis or Ghost), clone the OS drive to the RAID drive. A clock for 2017 How can I make these winter real estate photos look like summer photos? his comment is here So here is my WAG: maybe you need to have all 3 hard drives connected to break the RAID and change to AHCI.

Save BIOS settings and exit. You can't go from 10 to 5 or 5 to 10 on most cards. windows-7 bsod raid-1 share|improve this question edited Mar 3 '12 at 22:22 Mark Booth 1,4681538 asked Jun 23 '10 at 21:43 happysencha 41113 Which controller is the SSD attached Shut down and restart the PC going first to the BIOS to make the AHCI setting.

The solution basically involves rebooting in Safe Mode, changing to AHCI in the BIOS settings, letting it boot in Safe Mode, and then restarting in Normal Mode again. To do this, follow these steps: Exit all Windows-based programs. If not you can just get the drivers from the MOBO's website. 4) Restart and configure your raid :) 5) You will have to format your drives when you turn it